Trustpilot

Carpet Python Setup

Everything you need for your Carpet Python Setup

High quality wooden vivariums to successfully house carpet pythons

All the right equipment to create your own Australasian jungle

Available in four different colours

Finance available. Buy now and get free next day delivery*

Step 1

Choose your housing colour

Select between Beech, Black, Oak or Walnut.

Setup Type Beech
Beech
Vivarium
Setup Type Black
Black
Vivarium
Setup Type Oak
Oak
Vivarium
Setup Type Walnut
Walnut
Vivarium

Step 2

Select your level of setup

Select between Silver, Gold or Platinum. Hover over products for a closer look.

Silver
Gold
Platinum

Silver Setup

Product Added Thank You
 

Gold Setup

Product Added Thank You
 

Platinum Setup

Product Added Thank You
Silver
Gold
Platinum

Silver Setup

Product Added Thank You
 

Gold Setup

Product Added Thank You
 

Platinum Setup

Product Added Thank You
Silver
Gold
Platinum

Silver Setup

Product Added Thank You
 

Gold Setup

Product Added Thank You
 

Platinum Setup

Product Added Thank You
Silver
Gold
Platinum

Silver Setup

Product Added Thank You
 

Gold Setup

Product Added Thank You
 

Platinum Setup

Product Added Thank You

Step 3

Select your optional extras

Want to spruce up the place with an extra plant or two?

Optional Extras

Product Added Thank You
Building your Carpet Python Setup

It's very easy to construct this carpet python setup. The vivarium and cabinet come with instructions and should take around 20 minutes per unit to make. They mostly use locking screws so don't worry if you make a mistake, they can be taken apart and re-built. Once the vivarium is constructed you will need to seal the joints inside with aquarium sealant. This will extend the life of your vivarium and keep the joints water resistant. Make sure the panels are all clean and as dry as possible before applying. Once applied you will want to leave the enclosure for at least 6 hours so the silicone can set and the fumes can disperse.

For the following sections the cables for each piece of equipment will be fed through the vents at the top of your enclosure's back wall. The Vivexotic range now include removable vents large enough to fit the entire plug through so you should not need to re-wire any plugs.

Creating the Basking Area

This enclosure is designed to get to 88-90 Fahrenheit on the hot end but still leave the other side cool. To do this you will need to choose one side of the enclosure to be your hot end and one side to be the cool end. All of your heating equipment needs to be placed in the hot end.

We provide our daytime basking temperatures using a single ceramic heat emitter, surrounded by a guard and controlled using a pulse proportional thermostat. This unit does not put out any light so it can be used for both the day time and night time heating. The ceramic heat emitter is screwed into your screw fit ceramic lamp holder. They are then fixed to the ceiling and surrounded by a guard which is also screwed to the ceiling. We usually keep our ceramics close to the back corner but you could leave a 2 inch gap between the guard and wall to make sure your animal cannot get trapped.

Controlling Temperatures

In this set up the ceramic heat emitter will be controlled by a pulse proportional thermostat. Setting the thermostat up is very easy. Your thermostat will have 3 wires attached to a central box, on the central box is a dial with a list of temperatures around it's face. One of the wires ends in a plug, this is plugged into your power source. The second wire will end in a socket, you plug your ceramic heat emitter into this. The third wire ends in a sensor, this can be fed into the enclosure through one of the bottom vents and should be fixed to the back wall around 1/3 of the way from the hot end and 1/3 of the way from the ceiling. On the face of the thermostat you will want to set the temperature to 88 Fahrenheit. This should ensure that 1/3 of the enclosure will be around 88-90 Fahrenheit all night. As the unit will only turn on when temperatures drop below 88 Fahrenheit it can be left on all of the time.

Lighting the Enclosure

As our main heat source does not produce any light we need to install a second unit to provide light during the day time. Having a regular day/night cycle will help keep your python happy and healthy. We have found the best way of doing this is with a low level and compact UVB unit. Simply attach this to the ceiling either running front to back or from the side into the enclosure and run for 12 hours per day.

If you have any concerns or need any further advise please let us know.