MistKing Products

This is the latest 4th generation Starter Misting System. It is basic in its design to act as a starting point for customization or to be used on a small scale the way it is. This system is based on a robust pump with our latest timer providing exceptional and reliable performance. It can easily run 1 nozzle or can be upgraded to as many as 10. If you're planning to run more than 10 be sure to upgrade the pump or order the Ultimate or Advanced Misting Systems.

This Starter Misting System v4.0 includes

• 24V DC misting pump, capable of running up to 10 nozzles. Pump is very robust and can run dry!!! This pump has been extensively tested for a long time in the field and in the factory and by us personally. It has extremely low failure rates and it simply WORKS! Custom manufactured for MistKing.com and is unique to us. Pump is adapted for 1/4" tubing and includes vibration dampening rubber feet
• Pump power adapter. (cUL listed)
• 1 Value L misting assembly. Assembly is tested and it includes our super low flow check-valved spray tip, custom crafted in black with an average droplets size of ~50 microns. Check-valved tips greatly reduces the post mist drip. These nozzles can be adjusted and positioned in any direction. Can be securely fastened to any surface up to 0.625" (5/8") or 1.5 cm thick. This misting assembly is patented at USPTO
• Reservoir bulkhead with O-ring and plug
• 15 feet of 1/4" black opaque tubing
• Digital Seconds Timer ST-24 - with instructions
• 5 tubing clips with screws
• Reference manual

Starter System can silently run 1 nozzle or as many as 10 nozzles. These misting systems have been applied in a multitude of applications, from patio cooling, reptile, amphibian terrarium/vivarium enclosures, growing shelves with orchids or exotic plants, hobby greenhouses, and even grocery and industrial applications. Major ZOOs, botanical gardens, educational institutions, corporations and individual hobbyists all recognized our dedication to quality and customer service and are using our systems throughout the world.

Please note: this kit does not include a reservoir.

Advanced Misting System with a 3/8" Backbone is a significantly more powerful system than the starter or ultimate. Unless you're going to exceed 20 nozzles, we do not recommend upgrading to this misting system. Features a pump capable of pressures up to 125psi. Supports from 10 to 70+ nozzles of your choice. Actual number of nozzles depends on the complexity of the system. Pump can run continuously for hours at a time, EVEN DRY! These pumps are manufactured specifically for MistKing and are very robust.

This is the 4th generation mistking system which includes the new seconds timer. If your need calls for a different timer, be sure to select it from the options on the right.

This Advanced Misting System v4.0 includes

• Large capacity diaphragm pump with 3/8" fittings
• 24V Power adapter - 110V (CE and cUL listed)
• 3/8" reservoir bulkhead with plug
• 3/8" Ball Valve
• 35 feet of 1/4" black opaque tubing (to connect nozzles)
• 15 feet of 3/8" black opaque tubing (to connect reservoir to pump and run nozzle 3/8" backbone)
• 12 Value "T" Misting Assemblies
• 3 Value "L" Misting Assemblies
• 2 Reducing Tee Connections (3/8" to 1/4")
• 1 Reducing Elbow Connections (3/8" to 1/4")
• 20 1/4" Tubing Clips
• 10 3/8" Tubing Clips
• Seconds timer ST-24
• Installation instructions

This kit can be used as is, just get a suitable size reservoir. If you intend to use more nozzles, we recommend extending the 3/8" tubing backbone and adding some extra Reducing Tee (link) connections and then splitting into 1/4" lines that will feed the individual misting assemblies. Alternatively you can use a 7 port manifold fed by 3/8" tubing or a combination of both.

We suggest using this kit as the backbone for a custom misting system. Just add parts, nozzles, tubing and expand on this work horse. If you need help designing a system that will fit your particular situation, please contact us. Hobbyists and ZOOs run their entire animal rooms based on this kit or multiple kit.

The new version of an exclusive MistKing Seconds timer is now available. This timer has very cool improvements over the old seconds timer. It works only with MistKing Misting Systems. It can be connected to a 110V or 220V system with no problems.

Main features of MistKing Seconds Timer ST-24

• Backlit LCD Control Panel
• 10 programmable events (P0-P9)
• Ability to precisely schedule start time for each program
• Ability to precisely set misting duration for each program
• Option to schedule each program either on a specific day of the week or repeating daily
• Manual override allows for misting without affecting timer setup
• This timer has a rechargeable battery that keeps settings in case of a power failure
• Low voltage, connects to existing MistKing power supply
• Designed specifically for use with MistKing misting systems

Example:

• P0: Mist 25 sec at 8:00 am every day of the week
• P1: Mist 2 min at 4:00 pm every day of the week
• P2: Mist 4 min at 7:00 pm every Wednesday only

With this timer you now have the freedom and total control. Mist for a few seconds in the morning then for a few minutes in the afternoon and set up a schedule as you please.

If you already own a misting system and either use a hardware store digital timer or even an old version of the MistKing seconds timer, remember that upgrading is very easy and takes seconds.

MistKing Repeat Cycle Timer is an ideal choice for aeroponic and other growers that use MistKing misting systems. You can now control misting with separate repeating ON and OFF intervals for day and night. This repeat cycle timer goes beyone flexible. While many other RCT rely on a photo cell to switch from day to night mode, we use the timers internal clock to accurately specify when the switch should occur. This is much more precise. In addition you can configure exact day and night mode starts. RCT-24 can be connected to a 110V or 220V system with no problems.

Main features of MistKing RCT-24

• Backlit LCD Control Panel
• Day & Night Modes with separate configurations for ON/OFF cycles
• Ability to precisely set when day & night modes start
• Manual override allows for misting without affecting timer setup
• This timer has a rechargeable battery that keeps settings in case of a power failure
• Low voltage, connects to existing MistKing power supply
• Designed specifically for use with MistKing misting systems

Example:

If you already own a MistKing misting system and either use a hardware store digital timer or even an old version of the MistKing seconds timer, remember that upgrading is very easy and takes seconds.

New product that works with any existing MistKing system. This controller works by constantly monitoring humidity on the probe. Based on current reading and required humidity HT-24 will activate the misting system as needed. Excellent choice when desired humidity needs to be achieved. It plugs directly into the 24V misting system power and not into an electrical outlet.

Main features of MistKing Hygrostat Controller HT-24

• Backlit LCD Control Panel
• Remote Humidity / Temperature Probe
• Ability to precisely set Day & Night humidity
• Ability to specify when Day & Night modes start
• Manual override allows for misting without affecting timer setup
• This timer has a rechargeable battery that keeps settings in case of a power failure
• Low humidity alarm
• Variance setting which allows for specific humidity drop before engaging the pump
• Low voltage, connects to existing MistKing power supply
• Designed specifically for use with MistKing misting systems

Example:

• Day: Maintain 75% humidity
• Night: Maintain 60% humidity
• Low Humidity Alarm: 40% (Will beep if RH will drop to 40%)
• Variance 5% (ie. will raise humidity to 75% but will allow for a drop to 70% before turning on the system again)

Great addition to a small greenhouse or anything where precise humidity control is required.

Value 3/8 to 1/4 plug-in reducer. Under some circumstances can be useful. Do not purchase to convert an advanced pump to 1/4. Used to connect 1/4 tubing to a 3/8 connection.

Specialty 3/8 to 1/4 reducing Tee. It has great uses when designing larger systems with a 3/8 backbone. Two ports fit 3/8 tubing and middle port fits 1/4 tubing

Specialty 3/8 to 1/4 reducing elbow. It has great uses when designing larger systems with a 3/8 backbone.

Value 1/4 inch valve.

Value 3/8 inch Tee. Ideal for splitting tubing into 2 directions. Connect multiple T connectors together and make a custom manifold.

Value Straight 1/4 Female to Female Union.

Value 3/8 inch elbow. Perfect for going around tight corners.

Make perfect cuts every time with this nifty tube cutter. Cuts at perfect 90 degree angles without bending the tubing. Cutter closes for safe storage. It also features a collet depresser on the back to easily press on collets while removing the tubing. This little tool makes installation much easier. Make every cut a perfect one.

Value 3/8 inch Ball Valve.

Plug in this valve into your pump AC/DC adapter and you'll transform your existing System into a totally drip less one. Comes with Y-connector. ZipDrip connects between the reservoir and the pump. Select what tubing size you have between the reservoir and the pump. Starter and Ultimate system are based on 1/4" and Advanced system uses a 3/8" feed to the pump.

Value 1/4 inch Plug In Run Tee Union.

Replacement fitting for use with Advanced pumps. Advanced pumps going over 20 nozzles must have 3/8 fittings like this one on both of the ports. 3/8 NPT male on one end and 3/8 push to connect fitting on the other end. Made of nickel plated brass, this fitting is highly durable. Push to connect for easy tube removal.

Value 1/4 inch collets & collet Locks. These are good to keep as spares in case anything would happen to a connection which may cause leakage.

Need extra 3/8 inch polyethylene close tolerance tubing? Tubing is black opaque and doesnt let light through, preventing algea growth. Rated up to 250psi. This tubing is used to connect the reservoir to the pump. You can also use it to connect the pump to a manifold before splitting off with the 1/4 tubing to individual nozzles

Replacement fitting that can be used on any MistKing Starter or Ultimate pumps. 3/8 NPT male on one threaded end and 1/4 push to connect fitting on the other end. Made of nickel plated brass, this fitting is highly durable. Push to connect for easy tube removal. Do not purchase this fitting for Advanced pumps.

Secure the 3/8 tubing with nylon clips. Perfectly sized for use with the 3/8 tubing. Use a nail or a screw to secure in place. Sold in Packs of 10 pcs.

Need extra 1/4 inch polyethylene close tolerance tubing? Order as much as you need and take extra - youll be glad you did! Tubing is black opaque and doesnt let light through, preventing algae growth. Rated up to 250psi. This is the tubing used in all MistKing misting systems and is used to connect the nozzles with each other.

Value 3/8 inch Bulkhead. Includes an O-ring.

Value 1/4 inch elbow. Perfect for going around tight corners.