Bulb guards

These lamp protector cages have a very fine wire mesh in order to prevent even very small animals from getting through to the lamp.

They are suitable for all Lucky Reptile luminaires with E27 sockets. The large Thermo Protect Lamp Cage can even be put over the Thermo Socket plus Reflector luminaires.

A bracket with a cut-out for the lampholder is attached to the terrarium ceiling with screws or even silicon. The lamp cage is then attached to the bracket and can be completely removed for a lamp change.

The Thermo Protect lamp cages also include a removable glare shield which is mounted on the inside in order that the animals cannot reach it and get burned.

These lamp protector cages have a very fine wire mesh in order to prevent even very small animals from getting through to the lamp.

They are suitable for all Lucky Reptile luminaires with E27 sockets. The large Thermo Protect Lamp Cage can even be put over the Thermo Socket plus Reflector luminaires.

A bracket with a cut-out for the lampholder is attached to the terrarium ceiling with screws or even silicon. The lamp cage is then attached to the bracket and can be completely removed for a lamp change.

The Thermo Protect lamp cages also include a removable glare shield which is mounted on the inside in order that the animals cannot reach it and get burned.

For re-fitting reflector clamp lamps or as spare part for the Thermo Socket plus Reflector lamps. These wiremesh protectors prevent animals from getting into contact with the bulb. They will also fit the popular Zoo Med Clamp Lamp Deluxe LF-11 and can be used for other lamps with similar diameter as well.

Made for spotlamps this guard will shield both the R63 and R80 basking lamps. It is designed to be used with angled fixed baton type holders mounted on a side wall of the vivarium. Manufactured from 1mm thick steel mesh, with a powder-coated finish in black.

Made for spotlamps this guard will shield both the R63 and R80 basking lamps. It is designed to be used with angled fixed baton type holders mounted on a side wall of the vivarium. Manufactured from 1mm thick steel mesh, with a powder-coated finish in white.

This guard is designed to be fitted in small vivariums where space is limited for a large spotlight guard. Fits neatly into a corner and is only to be used with very low wattage bulb to give a little background light and heat. Finished in black.

This guard is designed to be fitted in small vivariums where space is limited for a large spotlight guard. Fits neatly into a corner and is only to be used with very low wattage bulb to give a little background light and heat. Finished in white.

Aluminium top that is held in place by the bulb holder. The guard is then held in place by 2 screws. This makes for easier changing of the bulbs. Houses either R80 or R63 spotlight bulbs (bulb and bulb holder not included).

Size: 160 x 110 x 110mm

Heater Guards for spot lamps or small ceramic heaters to protect animals from burning themselves. Simple, lightweight but strong powder coated steel design that allows maximum light penetration. Unique hinged panel with double security fasteners that allows easy access to lamps without the need to remove the fixture. These guards have four mounting brackets and cut-out for cable entry to enable flush mounting to the roof of wooden vivaria.

L 12cm W 12cm H 22.5cm

Heater Guards for spot lamps or small ceramic heaters to protect animals from burning themselves. Simple, lightweight but strong powder coated steel design that allows maximum light penetration. Unique hinged panel with double security fasteners that allows easy access to lamps without the need to remove the fixture. These guards have four mounting brackets and cut-out for cable entry to enable flush mounting to the roof of wooden vivaria.

L 12cm W 12cm H 17cm

Heater Guards for spot lamps or small ceramic heaters to protect animals from burning themselves. Simple, lightweight but strong powder coated steel design that allows maximum light penetration. Unique hinged panel with double security fasteners that allows easy access to lamps without the need to remove the fixture. These guards have four mounting brackets and cut-out for cable entry to enable flush mounting to the roof of wooden vivaria.

Diameter 12cm Height 15cm

A quailty and robust vivarium heat guard by Repstyle. This guard is designed for simple installation and ease of maintainance. All our heat guards feature a quick access door for easy bulb changes, a generous cable gap for flush mounting and dual spring catches for added safety.

The WhitePython Ceramic Heat Guard & Reflector is an entirely unique product which exclusively fits the WhitePython Ultra Slim Heat Lamps.

Compared to regular ceramic heat guards which often measure over 25cm tall, the new combination of WhitePython products will reduce the overall height of your ceramic heating unit to just 16cm, with a diameter of 14cm.

What's more, with a built in custom reflector dome your heater will become more energy efficient, reducing the necessary output to achieve the required temperature whilst also reducing the heat that rises into the roof of the terrarium, thereby reducing the possible risk of fire hazards.

The Ceramic Heat Guard & Reflectors are available in 3 colours; Midnight Black, Leaf Green and Earth Brown. They feature an outer guard to protect your reptile against possible burns, an inner reflective dome to push heat downwards and finally, a removable mesh grille on the base for easy access to the ceramic heater.

Installation of this innovative heat guard is also made easy with the twist lock screw fittings. Unlike traditional heat guards where you need to struggle holding the unit in the terrarium whilst single handedly trying to screw through a small hole into the terrarium room, WhitePython has made this easy. Simply mark the screw holes into the terrarium roof, put the screws in, leaving just a small gap, then once your heat guard is ready to install, simply place over the screws, twist and then tighten. Easy.

The WhitePython Ceramic Heat Guard & Reflector is an entirely unique product which exclusively fits the WhitePython Ultra Slim Heat Lamps.

Compared to regular ceramic heat guards which often measure over 25cm tall, the new combination of WhitePython products will reduce the overall height of your ceramic heating unit to just 16cm, with a diameter of 14cm.

What's more, with a built in custom reflector dome your heater will become more energy efficient, reducing the necessary output to achieve the required temperature whilst also reducing the heat that rises into the roof of the terrarium, thereby reducing the possible risk of fire hazards.

The Ceramic Heat Guard & Reflectors are available in 3 colours; Midnight Black, Leaf Green and Earth Brown. They feature an outer guard to protect your reptile against possible burns, an inner reflective dome to push heat downwards and finally, a removable mesh grille on the base for easy access to the ceramic heater.

Installation of this innovative heat guard is also made easy with the twist lock screw fittings. Unlike traditional heat guards where you need to struggle holding the unit in the terrarium whilst single handedly trying to screw through a small hole into the terrarium room, WhitePython has made this easy. Simply mark the screw holes into the terrarium roof, put the screws in, leaving just a small gap, then once your heat guard is ready to install, simply place over the screws, twist and then tighten. Easy.

The WhitePython Ceramic Heat Guard & Reflector is an entirely unique product which exclusively fits the WhitePython Ultra Slim Heat Lamps.

Compared to regular ceramic heat guards which often measure over 25cm tall, the new combination of WhitePython products will reduce the overall height of your ceramic heating unit to just 16cm, with a diameter of 14cm.

What's more, with a built in custom reflector dome your heater will become more energy efficient, reducing the necessary output to achieve the required temperature whilst also reducing the heat that rises into the roof of the terrarium, thereby reducing the possible risk of fire hazards.

The Ceramic Heat Guard & Reflectors are available in 3 colours; Midnight Black, Leaf Green and Earth Brown. They feature an outer guard to protect your reptile against possible burns, an inner reflective dome to push heat downwards and finally, a removable mesh grille on the base for easy access to the ceramic heater.

Installation of this innovative heat guard is also made easy with the twist lock screw fittings. Unlike traditional heat guards where you need to struggle holding the unit in the terrarium whilst single handedly trying to screw through a small hole into the terrarium room, WhitePython has made this easy. Simply mark the screw holes into the terrarium roof, put the screws in, leaving just a small gap, then once your heat guard is ready to install, simply place over the screws, twist and then tighten. Easy.

Slim-line guard made specifically for use with the Reptile Radiator.

Slim-line guard made specifically for use with the Reptile Radiator.

Made for use with ceramic bulbs this guard will shield the 60w, 100w and 150w type heaters. It is designed to be used in conjunction with the pendant type ceramic holder. Manufactured from 1mm thick perforated steel, with a powder-coated finish in white.

Made for use with ceramic bulbs this guard will shield the 60w, 100w and 150w type heaters. It is designed to be used in conjunction with the pendant type ceramic holder. Manufactured from 1mm thick perforated steel, with a powder-coated finish in black.

Made for spotlamps this guard will shield both the R63 and R80 basking lamps. It is designed to be used with fixed baton type holders. Manufactured from 1mm thick steel mesh, with a powder-coated finish in black.

A quailty and robust vivarium heat guard by Repstyle. This guard is designed for simple installation and ease of maintainance. All our heat guards feature a quick access door for easy bulb changes, a generous cable gap for flush mounting and dual spring catches for added safety.

A quailty and robust vivarium heat guard by Repstyle. This guard is designed for simple installation and ease of maintainance. All our heat guards feature a quick access door for easy bulb changes, a generous cable gap for flush mounting and dual spring catches for added safety.