T5 UV controller
A range controllers for use with T5 UV tubes
Releases and directs essential UV in to your enclosure
Fast delivery available using a next working day courier
Excellent quality T5 lighting systems
Guranteed to arrive in good condition
-
Wattage
A new electronic fluorescent lighting controller range from Arcadia incorporating a waterproof (IP67) plastic housing, with remote mains switch, ULTRA SEAL IP67 lamp leads and two types of mounting clips for flexibility of installation.
This product is covered by our Safe Delivery Guarantee

A new electronic fluorescent lighting controller range from Arcadia incorporating a waterproof (IP67) plastic housing, with remote mains switch, ULTRA SEAL IP67 lamp leads and two types of mounting clips for flexibility of installation.
This product is covered by our Safe Delivery Guarantee

FEATURING HIGH FREQUENCY ELECTRONIC BALLAST
- Incorporates an electronic ballast designed for use with high output T5 lamps
- Complete with Ultra Seal lampholders and Stainless Steel Clips
- Long mains lead for easy mounting
- Independent lamp circuits, if one lamp fails the other will continue to run
- IP67 lamp holders can be used in vivariums with misting systems and in close proximity to water
- IP67 controller housing can be mounted inside the vivarium if required
Fitting Tips
The Arcadia Reptile Ultraseal lamp holders offer both keeper and animal total security against dangerous water ingress. To comply with the new waterproof lighting regulations we have designed and made this system to be IP67 or waterproof. This does however mean that the lamp holders must be tight. To enable the safe and easy fitting of lamps the following advice is given:
- Unscrew the lamp rings from the lamp holders.
- Use a very small amount of Vaseline on the rubber seal on the inside of the sealing ring to moisturise the rubber seal. Wipe away and overspill from the lamp holder and lamp.
- Slide the lamp ring over the lamp and carefully line up the pins on the lamp with the two holes inside of the lamp holder and push gently. The lamp should seat into the lamp holder with a slight click. Do not turn the lamp as the pins will sheer off.
- Slide the lamp ring back down towards the lamp holder and holding the lamp tight with one hand screw up the lamp ring until gently seated with the other.
- T5 lamp run hotter than T8 lamps and the rubber seal around the lamp sealing ring may stick to the lamp or degrade over time, these rings can be easily replaced with product code AB5R.
This product is covered by our Safe Delivery Guarantee

FEATURING HIGH FREQUENCY ELECTRONIC BALLAST
- Incorporates an electronic ballast designed for use with high output T5 lamps
- Complete with Ultra Seal lampholders and Stainless Steel Clips
- Long mains lead for easy mounting
- Independent lamp circuits, if one lamp fails the other will continue to run
- IP67 lamp holders can be used in vivariums with misting systems and in close proximity to water
- IP67 controller housing can be mounted inside the vivarium if required
Fitting Tips
The Arcadia Reptile Ultraseal lamp holders offer both keeper and animal total security against dangerous water ingress. To comply with the new waterproof lighting regulations we have designed and made this system to be IP67 or waterproof. This does however mean that the lamp holders must be tight. To enable the safe and easy fitting of lamps the following advice is given:
- Unscrew the lamp rings from the lamp holders.
- Use a very small amount of Vaseline on the rubber seal on the inside of the sealing ring to moisturise the rubber seal. Wipe away and overspill from the lamp holder and lamp.
- Slide the lamp ring over the lamp and carefully line up the pins on the lamp with the two holes inside of the lamp holder and push gently. The lamp should seat into the lamp holder with a slight click. Do not turn the lamp as the pins will sheer off.
- Slide the lamp ring back down towards the lamp holder and holding the lamp tight with one hand screw up the lamp ring until gently seated with the other.
- T5 lamp run hotter than T8 lamps and the rubber seal around the lamp sealing ring may stick to the lamp or degrade over time, these rings can be easily replaced with product code AB5R.
This product is covered by our Safe Delivery Guarantee

High Frequency Electronic Ballast
- Incorporates an electronic ballast designed for use with high output T5 lamps
- Complete with Ultra Seal lampholders and Stainless Steel Clips
- Long mains lead for easy mounting
- Independent lamp circuits, if one lamp fails the other will continue to run
- IP67 lamp holders can be used in vivariums with misting systems and in close proximity to water
- IP67 controller housing can be mounted inside the vivarium if required
- Mini plug and socket connector on lamp holder leads, allows the lamp holders to be detached from main unit
Fitting Tips
The Arcadia Reptile Ultraseal lamp holders offer both keeper and animal total security against dangerous water ingress. To comply with the new waterproof lighting regulations we have designed and made this system to be IP67 or waterproof. This does however mean that the lamp holders must be tight. To enable the safe and easy fitting of lamps the following advice is given:
- Unscrew the lamp rings from the lamp holders.
- Use a very small amount of Vaseline on the rubber seal on the inside of the sealing ring to moisturise the rubber seal. Wipe away and overspill from the lamp holder and lamp.
- Slide the lamp ring over the lamp and carefully line up the pins on the lamp with the two holes inside of the lamp holder and push gently. The lamp should seat into the lamp holder with a slight click. Do not turn the lamp as the pins will sheer off.
- Slide the lamp ring back down towards the lamp holder and holding the lamp tight with one hand screw up the lamp ring until gently seated with the other.
- T5 lamp run hotter than T8 lamps and the rubber seal around the lamp sealing ring may stick to the lamp or degrade over time, these rings can be easily replaced with product code AB5R.
This product is covered by our Safe Delivery Guarantee

High Frequency Electronic Ballast
- Incorporates an electronic ballast designed for use with high output T5 lamps
- Complete with Ultra Seal lampholders and Stainless Steel Clips
- Long mains lead for easy mounting
- Independent lamp circuits, if one lamp fails the other will continue to run
- IP67 lamp holders can be used in vivariums with misting systems and in close proximity to water
- IP67 controller housing can be mounted inside the vivarium if required
- Mini plug and socket connector on lamp holder leads, allows the lamp holders to be detached from main unit
Fitting Tips
The Arcadia Reptile Ultraseal lamp holders offer both keeper and animal total security against dangerous water ingress. To comply with the new waterproof lighting regulations we have designed and made this system to be IP67 or waterproof. This does however mean that the lamp holders must be tight. To enable the safe and easy fitting of lamps the following advice is given:
- Unscrew the lamp rings from the lamp holders.
- Use a very small amount of Vaseline on the rubber seal on the inside of the sealing ring to moisturise the rubber seal. Wipe away and overspill from the lamp holder and lamp.
- Slide the lamp ring over the lamp and carefully line up the pins on the lamp with the two holes inside of the lamp holder and push gently. The lamp should seat into the lamp holder with a slight click. Do not turn the lamp as the pins will sheer off.
- Slide the lamp ring back down towards the lamp holder and holding the lamp tight with one hand screw up the lamp ring until gently seated with the other.
- T5 lamp run hotter than T8 lamps and the rubber seal around the lamp sealing ring may stick to the lamp or degrade over time, these rings can be easily replaced with product code AB5R.
This product is covered by our Safe Delivery Guarantee

T5 UV Starer Units
A range of UV starter units for use with T5 bulbs. The connectors on these units are a standard T5 fitting meaning they are compatible with all T5 fluorescent tubes. There are a variety of wattages available to ensure we have the optimal controller for use with your T5 tube.
When choosing your T5 unit you need to think about the wattage of the bulbs you are going to use. A controller with too lower wattage will not provide enough energy for the tube to work effectively while a controller with too higher wattage may blow the bulb or burn it out quicker than expected.
We have also included a range using standard fittings for dry enclosures and a range using waterproof seals for use in enclosures that have high humidity or need to be sprayed.